Repairs to uPVC Windows
uPVC windows are a great option for modern homes. They are durable, long-lasting and easy to maintain. As opposed to aluminium and timber they don't get rusty or decay.
It is crucial to wash and oil UPVC doors and windows on a regular basis. This will help avoid unnecessary repair costs and increase energy efficiency.
1. Broken Glass
The damaged glass in your windows can cause serious damage to your home and even be fatal. You should take the time to make sure that your windows are in good condition.
For single pane windows it is relatively easy to replace windows, and the new one is usually able to fit into the frame of the previous one easily. However, if windows with double panes are held in place by internal beading, it will be more difficult to take out the existing panes and install new ones. In this case you'll need to locate some plastic spacers that will aid the new pane in being able to fit perfectly into the window frame.
If you plan to attempt to remove the window panes yourself, it is essential to wear the appropriate safety equipment, including thick gloves and protective eyewear. It is also a good idea to lay down a drop cloth prior to when you begin working on the glass so that any fragments of glass fall on the fabric instead of onto the floor where they can be trodden under and cause further damage.
It's a great idea to cover the gap with tape after the glass is removed. This will keep drafts and water from getting into your property until a professional is able to fix the window. This will also act as a barrier that will prevent any intruders from gaining entry into your home. If the gap is large, you might want to consider using an alarm door that comes with an integrated window, as it will provide the best of both worlds.
2. Sagging
Upvc windows and doors are a low-cost energy efficient, durable and long-lasting alternative to timber sash windows. However, over time they are susceptible to a range of issues, including sliding. A sagging uPVC window can cause issues with light, draughts and even security. If you notice that your uPVC window is beginning to sag it's important to act quickly to prevent the problem from becoming worse.
To fix a window that is sagging you can try to reposition the hinges. You'll first need to open the windows to get at the frame. You can then unscrew both the hinges on the top and bottom using a screwdriver, and then adjust them clockwise or counter-clockwise. Once you've adjusted the hinges, close the window and test it for fit. If you're happy with the fit, you can tighten the screws to ensure they remain in place.
If you can't reposition the hinges you may need to replace the seal. Over time, rubber seals lose their elasticity and become dry and cause them to loosen. If this happens, it's essential to replace the seal as soon as you can to ensure that your uPVC windows are watertight and draught-proof.
UPVC handles can also become loose. The majority of the time this is due to screws that have come loose over time. However, it could occur because the handle mechanism has worn out. It's relatively easy to repair a loose uPVC handle. First, you'll need close the window and perform an initial test fit. The corner joints of the sash should align with the casing joint. If it isn't then you can make use of a screwdriver to loosen the handle, and then reverse the mechanism back into the position it was in.
3. Water Leaks
It is crucial to take action if get up each morning to find mouldy walls and floors that are wet. Water leaks through windows can cause structural damage to your home, and hinder your ability to control the temperature inside your home. The most frequent reason for leaking uPVC windows is that the sealant around the frame is either damaged or is missing.
This is an easy fix that can be completed by any DIYer who get more info is competent. Based on the severity of the problem the old caulking might need to be removed before a new layer can be applied. When it is time to uPVC repair, you must avoid over-caulking. This will only make your window more difficult to clean and lower its energy efficiency.
Make sure that the drainage holes are free of debris inside them and that the sill pan is here properly angled to drain away from the window. In more serious cases you might need to consider replacing the window.
Moldy sills and rotten ones are other signs of water leakage. The mold thrives in damp environments and can quickly spread across the home.
If the leakage occurs between the double-glazed glass it is more likely the problem is related to the seal, not the frame. A uPVC specialist can fix this issue by replacing the glass seal. This will restore the full insulation of your windows.
4. Faulty Hinges
If your uPVC windows are brittle to open, or are loose and open in a breeze, it may be the hinges that are at fault. Any competent DIYer can replace the hinges in a matter of minutes.
Like any mechanical component hinges will wear out over time. It is essentially a simple procedure, but it is simpler when you have a person to help hold the frame up.
Verify that the uPVC hinges open and close in the right direction. Look for the arrows that are on each hinge to determine which direction the window should be opened.
Window hinges that aren't working properly could be the result of incorrectly opening the window in a particular manner or because of improper installation in the factory. Sending us photos through our website can often solve the issue. We are always happy to offer assistance.
Regular lubrication of hinges is also essential. Applying a light engineering lubricant to the hinges is a great way to do this. We recommend using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication will help the window operate and close more easily. www.repairmywindowsanddoors.co.uk It also helps prevent corrosion and reduce the possibility of sticking. This is recommended to be done at least once a year. WD40 or other solvent-based oils are not recommended as they can cause damage to your uPVC windows.
5. Draughts
Draughts in windows made of upvc can be caused by various factors. First, the hinges because of wear and tear, could become misaligned. This causes an opening to appear where the sash joins the frame. These can be easily repaired by giving them good clean, but in the event that they are beyond repair it may be necessary to get them re-aligned or replaced. Secondly the interlock, this is located on the hinge side of the window and can also be misaligned, and again it is possible to give them a thorough clean, however in certain cases, it may be necessary to have these replaced.
The next common reason for draughts is window seals. They are susceptible to being worn out or damaged over time and allow air to escape through the gaps. This can be prevented by replacing them with high-quality weatherstripping. Another option is to replace the window with low-emissivity glass. this will help to regulate indoor temperatures and again will website lessen the possibility of draughts.
The last way to reduce draughts effectively is by using a Draught-exclusion device. These are typically fabric tubes filled with a filler that can be hung over your window sill. They can keep your home warm by blocking cold air.
With a little maintenance and repair your windows made of upvc will provide excellent security and insulation for your home. It is crucial to keep in mind that all windows will eventually wear out and it may be more info more cost-effective to replace them than to repair them. If you are experiencing issues with your upvc window it is recommended to speak with an expert immediately.